Espen's Setups

I have multiple models I want to use with telemetry:

On these models, I want to at least have voltage sensors. In the future I would also like to add altitude and GPS to them all.

Multiplex FunCub

Hardware

Receiver: D8R-II
Analog Sensors: FrSky Voltage Sensor
Hub: xxxxx
Hub Sensors: GPS (xxx), Vario (xxx), Temp (xxx)

Model Setup

  • Description: FunCub
  • Model Type: Airplane

Channels

  • AD1 (Raw channel used to log the unfiltered values from the external Voltage Sensor)
    • Description: AD1 Raw
    • Source Channel: AD1
    • Unit: <blank>
    • Short Unit: <blank>
    • Offset: 0.0
    • Factor: 1.0
    • Precision: 0
    • Moving Average: 0
    • Spoken Cyclic: Not Checked
  • AD2 (Raw channel used to log the unfiltered values from the external Voltage Sensor)
    • Description: AD2 Raw
    • Source Channel: AD2
    • Unit: <blank>
    • Short Unit: <blank>
    • Offset: 0.0
    • Factor: 1.0
    • Precision: 0
    • Moving Average: 0
    • Spoken Cyclic: Not Checked
  • Cell Voltage (Show AD1 converted to Cell Voltage, averaged over 5 samples)
    • Description: Cell Voltage
    • Source Channel: AD1
    • Unit: volt
    • Short Unit: V
    • Offset: 0.0
    • Factor: xxxxx
    • Precision: 2
    • Moving Average: 5
    • Spoken Cyclic: Checked

Alarms

  • AD1 Alarm 1: Low - Lower than 99 (3.22 V)
  • AD1 Alarm 2: High - Lower than 91 (2.96 V)
  • AD2 Alarm 1: Off - Lower than 127
  • AD2 Alarm 2: Off - Lower than 200
  • RSSI Alarm 1: Low - Lower than 45
  • RSSI Alarm 2: Mid - Lower than 42

Align T-REX600 ESP

Hardware

Receiver: xxx
Analog Sensors: DIY 6S LiPo voltage Sensor
Hub: None
Hub Sensors: None

Model Setup

  • Description: T-REX600
  • Model Type: Helicopter

Channels

  • AD1 (Raw channel used to log the unfiltered values from the external Voltage Sensor)
    • Description: AD1 Raw
    • Source Channel: AD1
    • Unit: <blank>
    • Short Unit: <blank>
    • Offset: 0.0
    • Factor: 1.0
    • Precision: 0
    • Moving Average: 0
    • Spoken Cyclic: Not Checked
  • Cell Voltage (Show AD1 converted to Cell Voltage, averaged over 5 samples)
    • Description: Cell Voltage
    • Source Channel: AD1
    • Unit: volt
    • Short Unit: V
    • Offset: 0.0
    • Factor: xxxxx
    • Precision: 2
    • Moving Average: 5
    • Spoken Cyclic: Checked

Alarms

  • AD1 Alarm 1: xxx - xxx(xxx)
  • AD1 Alarm 2: xxx - xxx(xxx)
  • AD2 Alarm 1: xxx - xxx(xxx)
  • AD2 Alarm 2: xxx - xxx(xxx)
  • RSSI Alarm 1: xxx - xxx(xxx)
  • RSSI Alarm 2: xxx - xxx(xxx)

HobbyKing AT6 FunFighter

Hardware

Receiver: xxx
Analog Sensors: FrSky Voltage Sensor
Hub: None
Hub Sensors: None

Model Setup

  • Description: AT6
  • Model Type: Airplane

Channels

  • AD1 (Raw channel used to log the internal AD1 channel)
    • Description: AD1 Raw
    • Source Channel: AD1
    • Unit: <blank>
    • Short Unit: <blank>
    • Offset: 0.0
    • Factor: 1.0
    • Precision: 0
    • Moving Average: 0
    • Spoken Cyclic: Not Checked
  • AD2 Raw (Raw channel used to log the unfiltered values from the external Voltage Sensor)
    • Description: AD2 Raw
    • Source Channel: AD2
    • Unit: <blank>
    • Short Unit: <blank>
    • Offset: 0.0
    • Factor: 1.0
    • Precision: 0
    • Moving Average: 0
    • Spoken Cyclic: Not Checked
  • Cell Voltage (Show AD2 converted to Cell Voltage, averaged over 5 samples)
    • Description: Cell Voltage
    • Source Channel: AD2
    • Unit: volt
    • Short Unit: V
    • Offset: 0.0
    • Factor: 0.026
    • Precision: 2
    • Moving Average: 5
    • Spoken Cyclic: Checked

Alarms

  • AD1 Alarm 1: xxx - xxx(xxx)
  • AD1 Alarm 2: xxx - xxx(xxx)
  • AD2 Alarm 1: xxx - xxx(xxx)
  • AD2 Alarm 2: xxx - xxx(xxx)
  • RSSI Alarm 1: xxx - xxx(xxx)
  • RSSI Alarm 2: xxx - xxx(xxx)